Cable Tray Load Class and Span Calculation: A Worked Method with IEC 61537 and NEMA VE 1

How to calculate cable tray load class and support span using IEC 61537 and NEMA VE 1: UDL per metre, class conversions, a worked example and fixings.

Cable tray rarely fails because the steel corrodes through — it fails at commissioning or years later because the load class was guessed and the span stretched one bracket too far. Selecting tray is a five-step calculation: cable weight per metre, tray self-weight, a reserve for future circuits, class selection from verified tables, and the support reaction for the fixings. This guide walks the method and translates between IEC and NEMA conventions.

Cable Tray Load Class and Span Calculation: A Worked Method with IEC 61537 and NEMA VE 1 (news image 3)
bange blog 7

How Load Classes Are Defined

Two conventions dominate specifications, and tenders that mix them create silent errors:

  • IEC 61537 — the manufacturer declares a uniformly distributed working load (UDL) and the support span at which it applies, verified by type testing: the system is tested at 1.5 × the declared working load at the declared span. A tray that carries “2.0 kN/m” only means something together with its span: the same tray is verified at different UDLs at 1 m, 2 m and 3 m supports.
  • NEMA VE 1 — North American ladder and trough tray is grouped into working-load classes of 8, 12, 16 and 20 lb/ft (the class number is the load per foot of tray), published by the manufacturer against specific spans and widths. These figures are working loads, not ultimate loads.

Conversion between the two is arithmetic: 1 lb/ft = 4.448 N / 0.3048 m ≈ 14.59 N/m. Both standards also require the manufacturer to declare how the system deflects under the working load; published tables commonly limit mid-span deflection to a small fraction of span (verify the criterion in each manufacturer’s data rather than assuming one).

The Reference Table: NEMA Class, SI Equivalent and Typical Content

NEMA VE 1 classWorking load (lb/ft)Working load (N/m)Typical content (steel tray, moderate span)
Class 88≈ 117Control and light power runs; instrumentation
Class 1212≈ 175Mixed power and control, single-layer routing
Class 1616≈ 234Multi-layer power cables, motor feeds
Class 2020≈ 292Heavy power banks, parallel feeder groups
IEC 61537Declared UDL + span, verified at 1.5 × UDL — read the pair, never the UDL alone

Class content examples are illustrative; capacity always comes from the manufacturer’s verified span/load/deflection table.

The Five-Step Calculation

Step 1 — Cable load per metre

Take each cable’s datasheet mass (kg/m) and multiply by 9.81 for N/m. Example: 12 power cables at 2.8 kg/m each give 12 × 2.8 × 9.81 ≈ 330 N/m. Datasheet mass, not a rule of thumb — a 4-core 95 mm² copper cable and a screened control cable of the same width differ by multiples.

Step 2 — Tray self-weight and accessories

Add the tray’s own mass per metre (a 300 mm steel trough runs roughly 8–12 kg/m depending on gauge; confirm from the datasheet) plus covers, lids, separator systems and any splicing hardware. Covers matter: a lidded outdoor run carries meaningfully more dead load than the bare tray.

Step 3 — Reserve for the future

Common practice reserves 20–30% spare capacity for future circuits, agreed in the project specification. If the spare is intended to be filled, the class must already cover it — upgrading a loaded tray in place is far more expensive than buying one class heavier on day one.

Step 4 — Class and span selection from verified tables

With total UDL in N/m (and its lb/ft twin), select a tray whose verified span/load table shows your UDL at your intended support span. If the required UDL sits above the table at the wanted span, the options are: a heavier class or gauge, a shorter span, or splitting the load across two runs.

Step 5 — Support reaction and fixings

Each support carries R = UDL × span (in N). Example: 490 N/m at a 3 m span puts ≈ 1,470 N on each support point — before any seismic or dynamic allowance. Threaded rods, anchors and trapeze hardware are then selected for R with their own safety factors. A tray verified for the class but hung from undersized anchors still ends up on the floor.

Worked Example (Illustrative Method)

The numbers below are an example of the method, not a design. Always size from manufacturer data and the project specification.

  • Cables: 20 kg/m total (≈ 196 N/m) of mixed power and control, single layer with maintained spacing.
  • Tray with covers: 10 kg/m (≈ 98 N/m) → total installed ≈ 294 N/m ≈ 20.2 lb/ft.
  • Reserve 25% for future circuits: 294 × 1.25 ≈ 368 N/m ≈ 25.2 lb/ft.
  • That exceeds NEMA Class 20 (≈ 292 N/m) — so the design must either shorten supports to a span where the chosen tray’s IEC 61537-verified UDL reaches ≥ 368 N/m, select a heavier-gauge or reinforced tray class, or split the load across two runs. All three are resolved from the manufacturer’s verified tables, not by judgement.
  • Fixings: at a 2 m span, R = 368 × 2 ≈ 736 N per support point; rods and anchors sized for this plus any dynamic allowance from the project’s seismic code.

Application Scenario and Case Analysis

Scenario: Overhead route from substation to MCC room in a process plant

Site constraints. A 60 m overhead route shares a pipe rack with insulated HVAC mains; floor fixings are unavailable for the middle 12 m, pushing spans long. The plant is in a seismically active region. Maintenance wants 25% spare for a planned second MCC lineup.

Selection reasoning. The engineer lists every planned cable with datasheet mass, adds tray and cover weight, applies the 25% reserve, and selects a Class-16/20-equivalent tray from the IEC 61537-verified tables at a 2 m span — accepting intermediate supports from the pipe rack where the 12 m gap forces spans beyond the table, the run splits into two parallel trays of lower UDL instead of one overloaded tray. Supports, rods and anchors are sized for the reaction at the class working load with the seismic anchor load from the project’s seismic code applied as a horizontal demand.

Common mistakes. (1) Quoting “NEMA Class 12” without the span — a class number alone is not a capacity statement. (2) Counting cable weight but forgetting covers, future reserve, or both — the two omissions alone can exceed 30% of the real load. (3) Anchors selected for rod size convenience rather than the calculated reaction. (4) Outdoor runs ignoring ice, snow or wind pressure on covered tray where the climate demands it. (5) Assuming the class transfers between steel and aluminium of the same width — capacity is per product per span.

Acceptance points. Verify that the delivered tray series matches the one in the IEC 61537 test report behind the declared class; measure mid-span deflection at first full load against the manufacturer’s published value; check support spacing against the table span; record anchor type, size, installation torque or setting, and pull-test results where the specification requires them; confirm splice plates installed at every joint with the specified hardware.

Selection Checklist

  • Compute UDL from datasheet cable masses — never from visual fill.
  • Add tray, covers and accessories; state the reserve percentage in the specification.
  • Select class and span as a pair from the manufacturer’s verified tables.
  • Size fixings for R = UDL × span plus dynamic/seismic demand.
  • For outdoor routes, add environmental loads where the climate requires.

Quality Inspection Points

  • Delivered gauge, finish and profile match the ordered series (a class belongs to a series, not to “tray” generically).
  • Splice plates and hardware complete at every joint; bolts torqued.
  • Support spacing as per the design table; no improvised long spans between fixings.
  • Deflection at full load within the manufacturer’s published limit.

Supplier Audit Checklist

  • Ask for the IEC 61537 test report and check that the declared class, span and deflection match the published table you specified against.
  • Ask whether NEMA VE 1 class data and IEC 61537 data are published for the same series and gauges.
  • Ask how covers affect the declared load and deflection figures.
  • Check accessory compatibility: splices, expansion joints and bends must be from the same verified system.

FAQ

  • Does a higher load class mean better steel? It means higher verified working load at the declared span. Compare class-plus-span pairs, not adjectives.
  • How do I convert NEMA classes to N/m? Multiply lb/ft by 14.59 — Class 12 ≈ 175 N/m, Class 20 ≈ 292 N/m.
  • What safety factor does IEC 61537 use? The declared working load is verified by testing at 1.5 × that load at the declared span; the working load is what you design to.
  • Can I just halve the span when the load is heavy? Only if the manufacturer’s verified table supports the UDL at that span — halving the span changes the capacity, but by how much is product-specific.
  • Do covers change the class? Covers add dead load and can change deflection; include them in the calculation and confirm their effect in the manufacturer’s data.
  • How is seismic load handled? Seismic demand is a project-code question applied to supports and anchors; the tray class covers gravity UDL, and the anchorage must resist the calculated horizontal demand.
  • Is fill percentage a substitute for load calculation? No. Fill governs ampacity derating and cable life; load class governs structural capacity. A tray can be electrically fine and structurally overloaded at the same time.

Specify the Pair — Class and Span — Before Anything Else

BANGE Electric manufactures cable tray and cable ladder systems with declared load classes and support span tables, verified under IEC 61537, across hot-dip galvanized, stainless and aluminium finishes. If your next route needs a defensible load-class calculation, contact the BANGE engineering team with your cable schedule, span constraints and environment for a documented selection.

Requirements may vary by application, market, and applicable standard.

Share the Post:

Related Posts

LEAVE YOUR MESSAGE